10 Best
Frequency Transducers
-
Product Highlights- 3. the mixer is designed to be powered by a single supply, and the rf, if and lo ports have dc isolation capacitors for easy . the operating frequency of the rf and lo inputs can be as high as 500mhz. the if output is a single-ended voltage output. it has an output bandwidth of 250 mhz.
- 1. ad831 is a low distortion, wide dynamic range, single-chip mixer, suitable for rf-if conversion in hf and vhf receivers, second mixer in stations, dc-baseband conversion, and quadrature modulation and demodulation and frequency shift detection in ultrasound imaging and other applications
- 2. ad831 provides +24 dbm third-order , which can achieve -10 dbm lo consumption. it does not require high- lo drivers, and there is no corresponding shielding and isolation problems. therefore, compared with passive mixers, it can system performance, reduce system cost. .
- 4. a single resistor connected between pins and fb is used to set the gain. the amplifier has low dc offset characteristics, so it can be used for dc coupling applications such as dc-baseband frequency conversion and quadrature amplitude demodulation
- 5. with the output amplifier of the mixer and the best source impedance, the ssb noise of the mixer is 10.3 db at 70 mhz. unlike passive mixers, ad831 has no insertion loss, no external duplexer, and no passive termination.ad8362 has two working modes: measurement and controller. in 1, in the measurement mode, vout and vset
SHOWview product -
Product Highlights
- 3. the mixer is designed to be powered by a single supply, and the rf, if and lo ports have dc isolation capacitors for easy use. the operating frequency of the rf and lo inputs can be as high as 500mhz. the if output is a single-ended output. it has an output bandwidth of 250 mhz.
- 4. a single resistor connected between pins out and fb is used to set the gain. the amplifier has low dc characteristics, so it can be used for dc coupling applications such as dc-baseband frequency conversion and quadrature amplitude demodulation
- 2. ad831 provides +24 dbm third-order , which can achieve -10 dbm lo consumption. it does not require high- lo drivers, and there is no corresponding shielding and isolation problems. therefore, compared with passive mixers, it can system performance, reduce system cost. .
- 1. ad831 is a low distortion, wide dynamic range, single-chip mixer, suitable for rf-if conversion in hf and vhf receivers, second mixer in stations, dc-baseband conversion, and quadrature modulation and demodulation and frequency shift detection in ultrasound imaging and other applications
- 5. with the output amplifier of the mixer and the best source impedance, the ssb noise of the mixer is 10.3 db at 70 mhz. unlike passive mixers, ad831 has no insertion loss, no external duplexer, and no passive termination.ad8362 has two working modes: measurement and controller. in 1, in the measurement mode, vout and vset
SHOWview product -
Product Highlights
- 1. ad831 is a low-distortion, wide dynamic range single-chip mixer, suitable for downconversion of rf-if into hf and vhf receivers, second mixer in base stations, dc baseband conversion and modulation and demodulation in quadrature and frequency detection of changes in ultrasound images and other applications
- 4. only resistor connected between out and fb is used to set the gain. the amplifier has low dc compensation characteristics, so it can be used for dc coupling applications, dc baseband frequency conversion, and quadrature amplitude demodulation.
- 3. the mixer is designed to be powered by single power supply, and rf, if and lo ports have dc isolation capacitors for ease of use. the operating frequency of rf and lo inputs can reach 500mhz. if output is single-end voltage output. it has an output band of 250 mhz.
- 2. ad831 provides a third order point of +24 dbm, which can reach an lo consumption of -10 dbm. no power lo drivers required and no corresponding shielding and insulation issues. so compared to passive mixers, it can improve performance and reduce cost. .
- 5. the mixer output amplifier and the best source impedance, the mixer ssb noise is from 10.3db to 70mhz. unlike passive mixers, ad831 has no insertion loss, external duplexer or passive termination. ad8362 has working modes: power measurement and controller. in the 1, in the power measurement, vout and vset
SHOWview product -
Product Highlights
- L r isolation design - passive diode double balanced mixer features excellent l r isolation, the typical value is 40 db, suitable for hf and vhf receiver rf-if frequency, quadrature modulation and demodulation.
- Mini components design - passive diode double balanced mixer adopts mini components design, rf power is 50mw, if current is 40ma, compact and light weight.
- Pcb material - frequency transducers conversion module is made of high quality pcb material, operating temperature is -20°c to 85°c, storage temperature is -55°c to 100°c, which is sturdy and durable to use.
- Low conversion loss - passive double balanced mixer has low conversion loss. the conversion loss is 4.6db, rf/lo is 0.05 to 250mhz, can be used in dc-baseband frequency conversion and quadrature amplitude demodulation.
- Scope of applicable - this radio frequency module can be used as up converter, down converter, 2 phase modulator and demodulator or phase comparator, frequency move detection and other applications.
SHOWview product -
Product Highlights
- 1. ad831 is a low-distortion, wide dynamic range single-chip mixer, suitable for downconversion of rf-if into hf and vhf receivers, second mixer in base stations, dc baseband conversion and modulation and demodulation in quadrature and frequency detection of changes in ultrasound images and other applications
- 2. ad831 provides a third order intercept point of +24 dbm, which can reach an lo consumption of -10 dbm. no power lo drivers required and no corresponding shielding and insulation issues. so compared to passive mixers, it can improve performance and reduce cost. .
- 4. only resistor connected between out and fb is used to set the gain. the amplifier has low dc compensation characteristics, so it can be used for dc coupling applications, dc baseband frequency conversion, and quadrature amplitude demodulation.
- 3. the mixer is designed to be powered by single power supply, and rf, if and lo ports have dc isolation capacitors to facilitate your . the operating frequency of rf and lo inputs can reach 500mhz. if output is single-end voltage output. it has an output band of 250 mhz.
- 5. the mixer output amplifier and the best source impedance, the mixer ssb noise is from 10.3db to 70mhz. unlike passive mixers, ad831 has no insertion loss, external duplexer or passive termination. ad8362 has working modes: power measurement and controller. in the 1, in the power measurement, vout and vset
SHOWview product -
Product Highlights
- 4. only connected resistor between out and fb is used to set the gain. the amplifier has low dc compensation characteristics, so it can be used for dc coupling applications, dc band frequency conversion, and quadrature amplitude demodulation.
- 3. the mixer is designed to be powered by single power supply, and the rf, if, and lo ports have dc isolation capacitors for ease of use. the operating frequency of rf and lo inputs can reach 500mhz. if output is single-end voltage output. it has an output band of 250 mhz.
- 1. ad831 is a single-chip low distortion, wide dynamic range mixer, suitable for downconversion of rf-if in and vhf receivers, second mixer in stations, dc band conversion and modulation and demodulation in quadrature and frequency detection of changes in ultrasound images and other applications
- 2. ad831 provides a third order point of +24 dbm, which can reach an lo consumption of -10 dbm. no high power lo drivers required and no corresponding shielding and insulation issues. so compared to passive mixers, it can improve the performance of the and reduce the cost of the . .
- 5. with the mixer output amplifier and the best source impedance, the ssb noise of the mixer is 10.3db to 70mhz. unlike passive mixers, ad831 has no insertion loss, no external duplexer or passive termination. ad8362 has working modes: power measurement and controller. in the 1, in the power measurement, vout and vset
SHOWview product -
Product Highlights
- 3. the mixer is designed to be powered by a single supply, and the rf, if and lo ports have dc isolation capacitors for easy use. the operating frequency of the rf and lo inputs can be as high as 500mhz. the if output is a singleended output. it has an output bandwidth of 250 mhz.
- 4. a single resistor connected between pins out and fb is used to set the gain. the amplifier has low dc characteristics, so it can be used for dc coupling applications such as dcbaseband frequency conversion and quadrature amplitude demodulation
- 1. ad831 is a low distortion, wide dynamic range, singlechip mixer, suitable for rfif down conversion in hf and vhf receivers, second mixer in stations, dcbaseband conversion, and quadrature modulation and demodulation and frequency shift detection in ultrasound imaging and other applications
- 2. ad831 provides +24 dbm thirdorder , which can achieve -10 dbm lo consumption. it does not require high- lo drivers, and there is no corresponding shielding and isolation problems. therefore, compared with passive mixers, it can system performance, reduce system cost. .
- 5. with the output amplifier of the mixer and the best source impedance, the ssb noise of the mixer is 10.3 db at 70 mhz. unlike passive mixers, ad831 has no insertion loss, no external duplexer, and no passive termination.ad8362 has two working modes: measurement and controller. in 1, in the measurement mode, vout and vset
SHOWview product -
Product Highlights
- Using 1.6mm thick pcb double sided board, sturdy and durable, come with long service life
- The conversion loss is only 8.0db, and the noise figure is as low as 8.0db (ssb). this is a passive device and does not require power supply
- The product have large heat dissipation area, possess stable operation and long running time
- 35db high isolation between local oscillator and rf input, which is stable and reliable
- The interior is composed of double balanced microwave diodes, come with high reliability
SHOWview product -
Product Highlights
- 3. the mixer is designed to be powered by a single power supply, and the rf, if and lo ports have dc isolation capacitors for easy use. the operating frequency of the rf and lo inputs can be as high as 500mhz. the if output is a single-ended voltage output. it has an output bandwidth of 250 mhz.
- 2. ad831 provides +24 dbm third-order point, which can achieve -10 dbm lo power consumption. it does not require high-power lo drivers, and there is no corresponding shielding and isolation problems. therefore, compared with passive mixers, it can improve system performance, reduce system cost. .
- 1. ad831 is a low distortion, wide dynamic range, single-chip mixer, suitable for rf-if down conversion in hf and vhf receivers, second mixer in base stations, dc-baseband conversion, and quadrature modulation and demodulation and frequency shift detection in ultrasound imaging and other applications
- 4. a single resistor connected between pins out and fb is used to set the gain. the amplifier has low dc offset characteristics, so it can be used for dc coupling applications such as dc-baseband frequency conversion and quadrature amplitude demodulation
- 5. with the output amplifier of the mixer and the best source impedance, the ssb noise figure of the mixer is 10.3 db at 70 mhz. unlike passive mixers, ad831 has no insertion loss, no external duplexer, and no passive termination.ad8362 has two working modes: power measurement and controller. in figure 1, in the power measurement mode, vout and vset
SHOWview product -
Product Highlights
- Good performance: the mixer is designed for single power supply. the rf, if and lo ports have dc isolation capacitors for easy use. the operating frequency of rf and lo inputs can be as high as 500mhz.
- Advantage: the if output is a single-ended voltage output with a 250 mhz output bandwidth. a single resistor connected between the pins out and fb is used to set the gain.
- Easy to use: the ad831 rf mixer module provides +24 dbm third‑order intercept point, which can achieve ‑10 dbm lo power consumption, no need for high‑power lo drivers, no corresponding shielding and isolation issues.
- Application: the rf mixer module is a low distortion, wide dynamic range, single‑chip mixer, suitable for applications such as rf‑if down conversion in hf and vhf receivers, second mixer in base stations, dc‑baseband conversion, etc.
- Quality assurance: this mixer module is manufactured under strict quality control and standard requirements, and has a high safety factor, so it can be used with confidence.
SHOWview product
Coupon copied
