10 Best
3d Printer Controllers
-
Product Highlights- I2c, spi and wifi interfaces are reserved for convenience of diy
- More fan interfaces: 1 way cnc fan, 3 way normally open fan
- Using 32bit main frequency 100mhz arm level cortex-m3 series lpc1768 microprocessor
- Double z-axis interface, eliminating the trouble of external drive expansion module
- Plug-in external dc5v power supply module to supply power to tft screen, bltouch
SHOWview product -
Product Highlights
- Driver - tmc2208 driver and marlin 1.1.8 for v1.1.5 board, while tmc225 driver and marlin 2.0.1 for v4.2.7 board bootloader pre-installed on both version boards.
- The thermal runaway protection is activated. the circuit board is circuit optimised and effectively solves the heating problem.
- Super quiet. ender 3 pro upgrade 32bit motherboard v4.2.7 compatible with creality ender 3, ender 3 pro, ender 3 v2 3d printer please note: it is just plug and play for ender-3 and ender 3 pro. if you want to install it on ender-5, please flash the ender-5 firmware. you can download the firmware here. https://www.creality.com/download
- Update firmware - please copy the firmware file to a formatted sd card without any other files on it. turn off the printer and unplug the power cable. insert the sd card and power cord and turn on the printer. wait 10 seconds to complete the firmware update.
- If you have any problems or questions about the product, you can contact us at any time via amazon message. we have a professional technical team that gives you technical support as soon as possible.
SHOWview product -
Product Highlights
- 🌻【two working modes】tft35 e3 v3.0 touch screen support uart serial port screen mode(touch screen mode) and 12864 screen mode, it can replace original display of ender 3 3d printer.
- 🌻【firmware update】it is easy and convenient to update firmware by sd card,download from our github: https://github.com/bigtreetech,copy and save it to sd card.firmware must bed reserved ,then re-plug the sd card and wait to 10s.the firmware has been successfully updated.
- 🌻【32 bit high performance microprocessor】tft35 e3 v3.0 touch screen uses 32 bit arm level cortex-m3 series stm32f207vct6,120mhz frequency microprocessor, it is designed for ender 3 3d printer especially,which can perfectly replace the original lcd screen of ender3 printer.
- 🌻【more extension ports is reserved】tft35 e3 v3.0 display reserve the extension port of filament breaking detection,automatic shutdown after printing,also wifi function can be realized by external wifi module through wifi port.
- 🌻【quality warranty 】this touch screen is designed and produced by bigtreetech team,any questions and feedback about that please free to tell us, we have professional technical team to support you.
SHOWview product -
Product Highlights
- It is designed to fit the entire electronics needed for a reprap in one small package for low the modular design includes plug in stepper drivers and extruder control electronics on an arduino mega shield for easy service, part replacement, upgrade-ability and expansion
- It has cartesian robots and requirements of the extruder
- Fully assembled & tested, no soldering required
- A number of arduino expansion boards can be added to the system as long as the main ramps board is kept to the top of the stack
- 0
SHOWview product -
Product Highlights
- 【practical and beautiful motherboard】: the appearance of the mainboard is very different from skr mini e3 v2.0 control panel, which enhances the aesthetics of the mainboards. it is a cool upgrade board. the usb interface is changed to usb micro b, which is more versatile and easy to use. it has a longer service life than mini usb, with up to 10,000 plug life and strengt...
- 【silent board】: increase the heat dissipation controllable fan of the whole machine, reduce the temperature of the whole machine when the device is working, and protect the board at every moment, so that the controller board has a longer service life. if you have problem that heating both bed and hot end not heat up, please contact us via amazon.
- 【high-performance stm chip】: the main silent control board adopts stmicroelectronics latest g0 series mcu stm32g0b1ret6, arm 32-bit cortex-m0 cpu, new chip, bring you a different use experience, for ender 3 , ender 3 v2 , ender 3 pro , ender 5 , cr10 3d printers.
- 【fast heat dissipation】: the design upgrade of the stepper motor driver heat sink increases the heat dissipation area and greatly improves the heat dissipation performance of the motherboard. the heat dissipation is faster, allowing the 3d printer motherboard to continue printing for a longer time.
- 【high accuracy and beautiful printing】: increase spi output port +3.3v power supply, external spi sensor power supply voltage +3.3v and +5v are optional. you can extend use the more types of sensors, sensors can be provide higher accuracy and print quality to make your prints more beautiful. the skr mini e3 v2.0 board only has 5v power supply from the spi output port. (...
SHOWview product -
Product Highlights
- 【professional design】our temperature controller use in cold weather,when temperature lower than 75f/24c, will cause so many problems in lcd dlp 3d print. such as print not sticking to the bed, layer adhesion, warming, and so on. finally, printing fails. our heater can rise temperature fast.
- 【small size】our 3d printer thermostat 10.8x5.7x3.2cm/4.25x5.24x1.25 in, 117grams, prefect for 8-15 inch lcd/dlp 3d printer, it only takes 10 minutes from 40f to 80f, for use in cold weather.
- 【use for】3d printer mini heater designed for 3d printers, it is small but powerful, for use in cold weather. it helps you to heat up the resin and rise the ambient temperature. make your 3d printer work well, save your time and resin material.
- 【professional design】our 3d printer heater built in high-precision temperature sensor, accurate to 0.1 ℃. fireproof case, high-quality power cord, all professionally designed for your safe printing.
- 【function】d3 printer air controller contains three functions, one is heating, one is air circulation, and the other is filtering. when the temperature is lower than the set temperature, start heating; when the temperature reaches the set temperature, start fan circulation. built in a small activated carbon filters, which can filter odor.
SHOWview product -
Product Highlights
- 🏆【get it going with no hitch】:creality sonic pad can connect to almost any fdm 3d printer on the market via a usb cable, 21 creality printers have been pre-configured for ender-3 v2, ender-3 s1, ender-3 s1 pro, ender-3 pro, ender-5 plus, ender-3 max, ender-3 s1 plus, cr-10 smart, cr-10s pro v2, cr-10 v3, ender-5 s1, ender-5 pro, ender-6, ender-7, ender-3 max neo, cr-10,...
- 🏆【intuitive model preview】:creality sonic pad supports g-code model preview when slicing with the creality print, ultimaker cura, pursa slicer, and super slicer.
- 🏆【highly integrated with strong computing power】:beneath the large 7-inch touch control screen, the klipper firmware runs in full swing on a powerful 64-bit computing platform. with software-hardware integration, you will get stunning performance, but with less trouble.
- 🏆【speed up printing while keep the quality】:creality sonic pad uses precision-oriented algorithms to command the motors for higher printing speed. the built-in input shaper fanction will mitigate oscillation during high-speed printing and smooth out ringing, thus keeping the model quality.
- 🏆【deft with user-defined macros 】:creality sonic pad supports user-defined programmable macros, with each macro combining a series of commands to a specific function for higher efficiency.
SHOWview product -
-
Product Highlights
- It contains a sd-card reader and an rotary encoder
- Easy to connect to ramps board with the included smart adapter
- Support 8 gb
- Graphic smart controller with 128 x 64 dot matrix lcd 12864 display
- With a sd card base on back, put slicing file into the sd card and select the file on the lcd, then can be printing
SHOWview product -
Coupon copied
